Please verify the polarity of the connector before using this battery as it may differ from the image
The DFRobotShop Rover V2 – Arduino Compatible Tracked Robot (Basic Kit) is a versatile mobile robot tank based on the popular Arduino Uno R3 USB Microcontroller . The Rover uses the popular Tamiya twin motor gearbox and the Tamiya track and wheel set. The DFRobotShop Rover PCB incorporates a standard Arduino Uno (surface mount ATMega328), L293B motor driver (connected to pins 5 to 8), voltage regulator and prototyping area while contributing to the mechanical structural of the robot. The onboard voltage regulator allows the entire board to be powered using as little as 3.7V to ~9V*.
Important Note: If you are using the 4xAA battery pack, please remove the LiPo jumper located at the left rear of the board.
In order to make assembly as easy as possible, solderless quick connect terminals have been included to give customers the option of crimping the wires to the motors (soldering is still preferable). The DFRobotShop Rover is compatible with a variety of shields when used at the same time as the motor driver, and is compatible with all shields when not using the motor driver. Additional features include 2x encoder connectors connected to A0 and A1 for use with the Encoder Pair for Tamiya Twin Motor Gearbox , pinout for DFRobot Bluetooth and DFRobot APC220 RF modules as well as 6x cool blue LEDs (jumper selectable) placed around the board. "DFRobotShop" = "DFRobot" + "RobotShop" (a.k.a. "DFRover").
*Note that the Tamiya Twin-Motor Gear Box included with the kit operates at 4.5V nominal. For 6V motors purchase 2x RB-Pol-202.
Features
Arduino compatible and shield stackable
Based on ATMEGA328 surface mount chip (Uno design) and L298P H Bridge
Incorporates dual H-bridge for bi-directional motor control (digital pins 5, 6, 7 and 8)
Voltage regulator included (connected to battery input and 3.5mm barrel connector)
Two XBee slots with breakout pins (switch selects which is connected to Tx/Rx) - headers sold separately
Solder prototyping area
Easy connection to DFRobot Bluetooth and APC220 wireless modules
“Universal connection point” at the front of the robot (see user guide for compatibility)
6x Blue LEDs around the board for effect (selectable via jumper LED_SEL)
In-system programming via ICSP
4x LEDs to indicate motor direction
Fully assembled DFRobotShop Rover PCB
DFRobotShop Rover aluminum frame (left and right sides) and hardware
The instructions were not clear. The video was basically a slideshow, showing how the parts look like once it was assembled but they did not show the actual procedure of putting the parts together. Also, even though other customers and the website said that Arduino was an easy start into robotics, the Arduino website says that it is an Integrated Development Environment, which when I searched that up on Google, it says that computer programmers use it for software development, not some toy a little kid can play with. If want to buy this kit, remember to learn programming language and buy the Bluetooth accessories first, so that you can control it wirelessly and not waste a lot of time. Otherwise, you will be stuck playing with it at your computer desk, because it requires the USB cable to be commanded.
r
roodjulian
Aimer!
Bon produit. J'ai eu beaucoup de plaisir à l'assembler et à le programmer. Idéal pour les débutants comme moi. Ajout d'un module Bluetooth pour que je puisse contrôler avec mon téléphone. Ensuite, la reconnaissance vocale!
M
Michael
Amazing!
Such a fun project and the possibilities are endless. Already looking to add an addition rover to the fleet :)
M
Michael
Incroyable!
Un tel projet amusant et les possibilités sont infinies. Vous cherchez déjà à ajouter un rover supplémentaire à la flotte :)
F
Francisco
Great educational robot kit
Hi! I just assembled and tested this robot and it's a good robot kit for people thinking on some robotics with sensors, flexible enough and with Arduino support. The kit is very comprehensive to mount, with good instructions thanks to a video in Youtube from Robotshop. It is also simple yet powerful enough to expand it with sensors and other actuators thanks to the integrated Arduino board it has. The DC motors are simple but effective with the gears and the whole structure is light but robust. It brings also several simple programs so you can start using it after mounting it, and later develop your own robot and have even mor fun! I posted a full review also here, and probably more later after I add more stuff to it ;-) http://letsmakerobots.com/node/47761
If you are not satisfied with a product purchased from the Site, you may request a return within 30 days from the delivery date, unless the product is listed under the Return Exceptions below or is subject to specific return conditions noted on the product page.
This return policy also applies, as a minimum standard, to products sold and fulfilled by third-party vendors through the Marketplace.
Returns under this policy concern non-defective products. In the case of a confirmed manufacturing defect, remedies are handled under the Warranty terms, at the Vendor's discretion. See the Warranty section.
Return Conditions
To qualify for a refund under the 30-day return policy, all of the following conditions must be met:
A valid Return Authorization (RA) number must be obtained prior to returning the product. Returns without an RA number will be refused.
The RA number is valid for 30 days. The returned item must be received within that period.
The RA number must be included with the return.
Products must be returned in unused, unmodified condition (e.g., no scratches, alterations, missing parts, or signs of installation/use) and in their original packaging, suitable for resale.
Shipping fees are non-refundable. Return shipping costs are the responsibility of the customer, except in cases of a product confirmed defective through RobotShop's troubleshooting process or of a verified shipping error by RobotShop.
Refunds are processed within 7 days after receipt and inspection of the returned item.
A $100 cleaning fee may apply to domestic robots returned in used or unclean condition.
A 20% restocking fee may apply to large-quantity returns of items ordered specifically for the customer from the manufacturer or not part of RobotShop's standard inventory.
Return Exceptions
The following products are not eligible for return or refund under this policy:
Used, damaged, or modified products — Items that show signs of use, wear, or alteration, making them unsuitable for resale.
Consumables — Use and wear-and-tear components, altered or depleted through use (e.g., batteries, belts, brushes, gears, filament, tires, disposable bags, lubricants, greases, waxes, etc.). Not eligible for return once opened or used.
Perishables — Goods liable to deteriorate or expire rapidly. Not eligible for return.
Sealed goods (health or hygiene) — Items sealed for health-protection or hygiene reasons (e.g., masks, gloves, odor-absorbing products). Not eligible for return once unsealed.
Build-it-yourself products and items requiring customer assembly — Including robots & kits, robot parts, and other products requiring assembly or soldering. Not eligible for return once assembled, soldered, or installed.
Digital Goods, Software, and Apps — Final sale only, due to licensing restrictions.
Clearance Items — Products identified as clearance or final sale, including end-of-life or discontinued items.
Custom-made, personalized, or special-order items — Products manufactured, configured, adapted, or built to the customer's own specifications and requirements.
On-Demand Items — Standard catalogue products not stocked by RobotShop and ordered specifically to fulfill a customer request.
While the same return policy applies, these orders require a separate contact process for returns.
RobotShop Fulfilled Orders → submit a support ticket from your account under My Support Tickets.
Marketplace Vendor Orders → submit a ticket from your account under My Marketplace Tickets to contact the vendor directly.
Note: Marketplace vendor products are normally labelled with SKUs starting with RM, and identified on the product page with the mention "Sold and fulfilled by [Vendor Name]".